Menvier Security TS900+ Spezifikationen Seite 13
- Seite / 68
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
Tamper Switch.
Remote Keypad case tamper
ENT Key Disable.
If the “ENT” key is enabled the remote keypad can
be used to set/unset and access all user menus. If
the “ENT” key is disabled the remote keypad can
only be used to set and unset the system.
Installation Procedure.
Always ensure that all power (mains
and battery) is removed before
making any connections to the
remote keypad.
1. Separate the cover and base by using a
screwdriver to push 2 of the clips (top or
bottom) inward from the base indents, then lift
the cover assembly, noting that the PCB is fixed
to the under side of the cover.
2. Hold the base in position (keyhole to the top)
and mark the three securing holes, drill and
plug the wall as required. Pass all the cables
into the base via the cable entry points as
appropriate and secure the base to the wall.
3. Connect “Remote Network” and detection
circuit cables to the appropriate terminals, see
Figure 8.
4. Set the I/D selector jumper link to the required
position:
I/D Selector Circuit A Circuit B
Panel
Output
109105
211126
313147
415168
ENG/NULL N/A N/A N/A
l
No two remote keypads or LECs should
have the same I/D.
l
If the I/D is set to “ENG” the remote keypad
will function as an Engineer’s keypad
allowing it to be plugged onto the control
panel so that system programming and
testing may be carried out (see Engineer’s
Keypad).
5. If the remote keypad has a "ENT" key
enabled/disable link it can be used to limit the
functionality of the remote keypad. If the "ENT"
key is enabled the remote keypad can be
used to set/unset and access all user menus. If
the "ENT" key is disabled the remote keypad
can only be used to set and unset the system.
6. If the remote keypad has a “Ward Sounder
Control” link it can be used to make the remote
keypad sounder follow the programmable
output. When the link is set to the disabled
position the sounder responds as normal.
9
TS790 & TS900 Installation Manual System Installation
I/D
Selector
REMOTE
I/D
LED MIMIC
ENT KEY
DISABLED
1
2
3
4
ENG
WARD SOUNDER
CONTROL
ABCDE
SPK
+
1 2
3
5
4
67
89
Display Module
O/P
-
Figure 8. NETLCD, NETLED & NETARM PCB Layout
I/D
Selector
REMOTE
I/D
LED MIMIC
ENT KEY
DISABLED
1
2
3
4
ENG
WARD SOUNDER
CONTROL
4
5
Display Module
3
1
89
7
ABCDE
O/P
-
Figure 9. NETSTAR PCB Layout
- TS790 & TS900 1
- Overview 3
- System Installation 3
- Engineer’s Menu 1 3
- Engineer's Menu 2 3
- Engineers Menu 3 4
- Appendices 4
- System Architecture 5
- Control Panel 5
- Remote Keypads 6
- TS900 NODE 6
- ID Node (TS900.IDNODE) 6
- TS700 LEC 6
- Specifications 6
- Cable Routing 7
- Remote Network Wiring 8
- Control Panel Installation 9
- Control Panel PCB Layout 10
- NETLCD Remote Keypad 12
- NETSTAR Remote Keypad 12
- NETLED Remote Keypad 12
- NETARM Remote Arming Station 12
- PCB Layouts & Connections 12
- Tamper Switch 13
- ENT Key Disable 13
- Engineer’s Keypad 14
- Figure 11. TS900 Node Layout 15
- TS700 LEC Installation 16
- Wiring Detection Circuits 16
- External Sounder Connections 17
- Auxiliary Tamper 18
- Extension Loudspeakers 18
- Digicom/RedCARE Installation 19
- Plug-on Digicom Installation 19
- Connecting a Printer 20
- Programmable Outputs 21
- Pre Power-Up Checks 22
- Initial Power-Up 22
- Power-Up Checks 23
- NVM Defaults 23
- Introduction 25
- Panel Outputs 26
- Digicom Outputs 26
- Digicom Channels 26
- Programmable Output Types 26
- Program Circuits 29
- Circuit Attributes 30
- System Timers 31
- Setting Modes 34
- Do System Print 34
- Remote Reset Algorithm 35
- Configuration 35
- Goto User Menu 1 37
- View Location Text (LCD Only) 38
- Relearn Hardware 38
- View Circuits 40
- Set System Time 40
- Set System Date 40
- Change Passcode 40
- Chime Circuits 41
- Alter 24Hr Group 41
- Print System Log 41
- Configure Wards 41
- Log Event Codes 42
- View System Log 42
- StarburstLCD 44
- Menu Contents 45
- Time Switches Flowchart 46
- Part Set Group Operation 47
- Code Set Group Operation 47
- Reset Message 48
- Banner Message 48
- Location Text 49
- Printer Header 49
- Part Set Banner 49
- Current Consumption 49
- View Inactive Circuits 50
- Custom Outputs A & B 51
- Modem Options (LCD Only) 52
- Program Digi Flowchart 53
- Reset Digicom 54
- Point ID Extended Reporting 55
- Workshop Canteen 59
- Service Department 59
- Key Point Application Example 60
- Text Editing Keys 62
- Setup New Users 63
- Setup New Users Flowchart 64
- 496487 Issue 3 68
Verwandte Produkte und Handbücher für Sicherheitszugriffskontrollsysteme Menvier Security TS900+
(16 Seiten)© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.033 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern